Previous productPancake Die 918.2 Extra Sma...
Next productPancake Die Large Wonky Sta...
Picture of Pancake Die 597 Fleur de Lis Picture of Pancake Die 597 Fleur de Lis

Pancake Die 597 Fleur de Lis

This Fleur de lis die is quite popular. It is a little more difficult to remove the metal from the die when cut due to the complexity of the cut - but it works. This die measures 1 5/8" x 1 1/8"
SKU: PD 597

Potter USA Pancake Die Information:

  1. The pancake dies are designed to cut non-ferrous metal (copper, silver, brass, gold, nickel) 20 gauge and thicker to about 16 gauge.
  2. They work best when the metal is hard. If the metal is too soft, you will get a burr and it will be difficult to remove your part from the die. DO NOT ANNEAL METAL FIRST.
  3. The dies only work in one direction - with words FACE DOWN
  4. I will send them to you pre-sprung so that you know where to put the metal.
  5. If you use metal that is too thick or too thin, it is possible to damage the die.
  6. As long as you stay within the recommended gauges, the dies should last you many years under normal use.
$27.50
increase decrease
Availability: In stock
Ship to
*
*
Shipping Method
Name
Estimated Delivery
Price
No shipping options

Potter USA Pancake Die Information:

  1. The pancake dies are designed to cut non-ferrous metal (copper, silver, brass, gold, nickel) 20 gauge and thicker to about 16 gauge.
  2. They work best when the metal is hard. If the metal is too soft, you will get a burr and it will be difficult to remove your part from the die. DO NOT ANNEAL METAL FIRST.
  3. The dies only work in one direction - with words FACE DOWN
  4. I will send them to you pre-sprung so that you know where to put the metal.
  5. If you use metal that is too thick or too thin, it is possible to damage the die.
  6. As long as you stay within the recommended gauges, the dies should last you many years under normal use.
Customers who bought this item also bought
Picture of Pancake Die 599 Shelli's Flower

Pancake Die 599 Shelli's Flower

PD 599
This die is 1 inch in diameter. This is an intricate die and can be difficult to remove the cut piece from the die, but it works. Just have patience! Please note: This die requires some deburring after stamped our, use flush cutters and file.
$27.50
Picture of Pancake Die Opener

Pancake Die Opener

PDopener
Pancake Die Opener
$14.00
Picture of Urethane Pieces

Urethane Pieces

UP
Bag of 10 pieces of urethane for use with impression dies. 95 durometer sheet. Pieces range from approximately 1/2 inch squares. Thickness of each piece is 1/4 inch. Note: These will fray, crack and deform with use, but you will get many uses from them.
$8.50
Picture of Aluminum Spacer (4.5” x 7.75” x 1”)

Aluminum Spacer (4.5” x 7.75” x 1”)

Al-Spacer
This spacer is 4.5'' x 7.75'' and 1'' thick. Non magnetic Spacers are used in the press to lessen the amount of effort needed to extend the jack and activate the items being used in the press. Top and bottom platens are not meant to touch - it will cause the jack to overextend and cause leaking, or for jack to fail. Always use spacers on lower platen to take up space between platens.
$34.75
Picture of Pancake Die 564 Small Cross

Pancake Die 564 Small Cross

PD 564
Pancake Die Small Cross 1.5 inches tall by 1 inch wide
$27.50
Picture of Pancake Die 628 Large Flower

Pancake Die 628 Large Flower

PD 628
This flower is one of the pancake dies that needs deburring on the back after cutting it out with the pancake die with flush cutters. Design: 1.9" diameter
$29.50