This shape is meant to be folded in half to create a keychain - no need for soldering! Shape - 4-3/8" x 1-3/16" Die itself - 5-5/8" x 6-3/8"

This shape is meant to be folded in half to create a keychain - no need for soldering! Shape - 4-5/16" x 1-1/8" Die itself - 5-5/8" x 6-3/8"

The Standard Die Shoe is more durable and will last longer than the High-production Die Shoe, due to the smaller size of the hole in the base offering more support to the Die Sets (available separately). Standard Die Shoe OR High-production Die Shoe REQUIRED FOR ALL FSS DIE SETS (available separately)! Die Shoes are interchangeable with different FSS Die Sets. Interchangeable FSS Standard Die Shoe Includes: Base with two sizes of pins to maintain correct indexing and assembly and center hole to assist with metal alignment and for removing cut blanks. Aluminum Pusher Plate with two oversized holes Two springs to place between the top and bottom of the Die Sets (Die Sets available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Design: 1-1/2" x 1" Oval Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Overall size: 2" x 6-7/8".

2" x 6-7/8"

Overall Design Size: approximately 2" x 6-7/8". The designs on this plate are very small. Each sun measures approximately 5mm. Designed for use in a rolling mill.

Design Size: approximately 2-15/16" x 5/16" Designed for use in a rolling mill.

An assortment of 10 small pieces of aluminum (sizes vary) that can be used to create a force when pressing impression dies. Sizes will vary from 1/2" - 1". Forces work best when the aluminum is pressed hot. ALWAYS CENTER YOUR WORK. Watch the following videos to see Kevin demonstrating how these work: https://www.facebook.com/groups/1253577991351417/?multi_permalinks=7886112968097853&ref=share AND https://www.facebook.com/1640860751/videos/807686980360120/

Overall size: 2" x 6-7/8". Designs from left to right measure: 7/8" x 1/2", 7/8" x 5/8", Center design measures 13/16" diameter, 5/8" x 1/2", 3/4" x 13/16", 3/4" x 5/8"

Design Size: approximately 2" x 6-7/8". Designed for use in a rolling mill. Sample earrings made by Erin Greenberg (shibori plate and the large guitar pick pancake and silhouette die bundle) https://potterusa.com/pancake-silhouette-die-bundle-large-guitar-pick

Design Size: approximately 2" x 6-7/8". Mandala Size: 1-1/4" diameter Designed for use in a rolling mill.

Design Size: approximately 2" x 6-7/8". Designed for use in a rolling mill. Sample by Lynette Andreasen.

Lucky Dog Club is now available any time! Previously, it was offered quarterly. Now, you can sign up whenever you’d like! Becoming a member of the Lucky Dog Club gives you free domestic shipping on all orders* for one year. All orders placed by members, whether you spend $5 or $1000+, ship free. This option is perfect for those who love our Dies of the Day and prefer to make multiple small purchases!

Design: 1-3/4" x 1-1/4". Die itself: 6-1/4” x 3-3/8”.

Overall Design Size: approximately 2" x 7" Left to Right Leaf Sizes - 15/16" x 1-3/8", 1-3/4" x 15/16", 1-3/8" x 3/4", 1-1/2" x 1-11/16" Designed for use in a rolling mill.

1-3/16" x 2-1/8". Die: 5-3/16" x 4-1/8". Matches RMP209

1-1/16" x 1-13/16". Die: 5-1/2" x 3-3/4". Matches RMP296

1-1/8" x 1-15/16". Die: 5-3/16" x 4-1/8". Matches RMP209

Overall size: 2" x 6-7/8". From Left to right: 1-7/16" x 13/16", 1-5/8"x5/8", 1-5/8" x 3/8", 1-1/2" x 13/16", 1-1/2" x 11/16", 1-9/16" x 13/16"

These stampings are direct from Janvier in France. Sold in sets of 2. Limited Quantity! 40 x 35.9mm. approx. 1.2mm thick.

These stampings are direct from Janvier in France. Sold in sets of 2. Limited Quantity! 71 x 38mm. approx. 1.5mm thick.

Design Size: approximately 2" x 6-7/8". Designed for use in a rolling mill.

Design- 2-3/4" x 13/16". Overall die measurements- 7-1/4" x 3-3/8"

Design: Design Size: 2" x 6-3/4"; ~1/8" thick

Design Size: 2" x ~6-3/16". Each strip of pattern is approximately 3/8" wide. This pattern plate pairs well with Pancake Die Bracelet B044A 3/8" Thin Bracelet, and Pancake Die Bracelet B044 1/2" Thin Bracelet. .

Design: 1-11/16" x 3". Die: 5-5/8" x 4-15/16".

This option is for LAYAWAY Payment for the Quick Form Press. The Quick-Form Press , invented in 2022 by Kevin Potter, combines the power of a kick-press with the ease of use of a hand-operated arbor press. The key to how this press operates is the cam. Unlike an arbor press, which has a linear force that limits the amount of pressure possible, the Quick-Form Press utilizes a cam that allows you to exert maximum force with minimal effort! Whether you're bending rings, cuff bracelets, napkin holders, or silverware, this all-in-one press provides a wide range of tooling for forming metal without the use of a hydraulic press. See the full description for all the details! The price Includes Free Domestic Shipping to the Continental US. Alaska, Hawaii, and international orders will require additional shipping charges. Please call for a shipping quote if you reside outside the continental US.

This option is for LAYAWAY Payment for the Quick Form Press. The Quick-Form Press , invented in 2022 by Kevin Potter, combines the power of a kick-press with the ease of use of a hand-operated arbor press. The key to how this press operates is the cam. Unlike an arbor press, which has a linear force that limits the amount of pressure possible, the Quick-Form Press utilizes a cam that allows you to exert maximum force with minimal effort! Whether you're bending rings, cuff bracelets, napkin holders, or silverware, this all-in-one press provides a wide range of tooling for forming metal without the use of a hydraulic press. See the full description for all the details! The price Includes Free Domestic Shipping to the Continental US. Alaska, Hawaii, and international orders will require additional shipping charges. Please call for a shipping quote if you reside outside the continental US.

Two delrin conforming formers in 2" and 1.5" diameter. Use ONLY with the Quick-Form Press, Former Adapter, and Flat Bracelet Formers. Large: 2" diameter. Mount on Former Adapter (sold separately) and use with Large (2") Flat Bracelet Former. Small: 1-1/2" diameter. Mount on Former Adapter (sold separately) and use with Small (1.5") Flat Bracelet Former. Use two washers with Former Adapter for Small Flat Conformer.

Use ONLY with the Quick-Form Press and Urethane Pusher. Large: 2" diameter. Mount to Tool Mounting Plate at 4th hole. Small: 1-1/2" diameter. 1-1/4" forming width. Must use with Small Tooling Adapter (included with press purchase). Mount to Tool Mounting Plate at 3rd & 5th holes. Use two washers with Urethane Pusher for Small Flat Former.

Overall Design Size: approximately 2" x 7" Designed for use in a rolling mill. **Formerly sold in the Halloween 2021 Mystery Box

Overall Design Size: approximately 2" x 7" Designed for use in a rolling mill.

6.4 x 22.6mm.

Two delrin conforming formers in 90° and 60° angles, and a corresponding steel angle forming mandrel. Use ONLY with the Quick-Form Press, Former Adapter, and Flat Bracelet Formers. The conformers must mount on the Former Adapter (sold separately).

Overall Design Size: approximately 2" x 6-7/8". Designed for use in a rolling mill.