Put a Spring in Your Step with these flowering cowboy boots, just in time for Rodeo season out west! Design: 1-3/16" H each Designed for use in a rolling mill.

Design: 3-1/2" x 2-1/2" Die itself: 7" x 5-1/2" Coordinated to work with the Oval Dish former die DF-006

plate is 2 x 7 inches long, each honeycomb is 4mm x 4mm Designed to be used in a rolling mill with annealed, non-ferrous metal.

Design: 3" diameter Die itself: 4 1/4" X 6 3/16"

11/16" Wide

2" x ~6-7/8". Each card size: 1-3/16" x 1-13/16"

3-1/16" wide (from the center of each side), 3-1/2" wide from point to point. Overall die size measurements 7-1/2" x 5-1/2". Coordinated to work with DF015 Dish Former Silhouette Die Hexagon. Will not fit in the discontinued medium PotterUSA press.

Now for bangles too! NEW bracelet forming frame, 2" 95 durometer urethane puck, and set of 4 formers. Please read the information below. Beam: 6"L x 3/4"H Columns: 2 1/2"H x 1 5/8"W (top), 2"W (bottom) Large Synclastic former: 2 7/16"W x 1 3/4"H Small Synclastic former: 1 7/8"W x 1 11/16"H Large Anticlastic former: 2 15/16"W x 1 3/4"H Small Anticlastic former: 1 15/16"W x 1 11/16"H

Design: 1" Circle Tag Shape w/Tab for a Jump Ring Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

1" x 9/16" (25mm x 15mm) Die: 5-3/16" x 3-3/8" This die is coordinated to work with the smaller shapes on Pattern Plate RMP287 Boho Leaves.

Overall Design Size: approximately 2" x 7" Designed for use in a rolling mill.

Overall size: 2" x 6-7/8".

Design: 1-5/6" x 1-3/4" each. Die: 6" x 5-1/2".

Overall Design Size: approximately 2" x 6-7/8". Designed for use in a rolling mill.

Overall Design Size: approximately 2" x 7" Designed for use in a rolling mill.

1 1/16" x 3/4" or 27.5mm x 19mm

This die must be used in a hydraulic press. This die measures 1 1/4" x 3/8"

Design: Heart 1-1/4" x 1-3/16" Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Design Size: approximately 2" x 6-7/8" Designed for use in a rolling mill.

This spacer is 4.5'' x 7.75'' and 1'' thick. Non magnetic Spacers are used in the press to lessen the amount of effort needed to extend the jack and activate the items being used in the press. Top and bottom platens are not meant to touch - it will cause the jack to overextend and cause leaking, or for jack to fail. Always use spacers on lower platen to take up space between platens.

Overall size: 2" x 6-7/8". From Left to right: 1-7/16" x 13/16", 1-5/8"x5/8", 1-5/8" x 3/8", 1-1/2" x 13/16", 1-1/2" x 11/16", 1-9/16" x 13/16"

2" x ~6-7/8".

2" x ~6-7/8".

1-1/4" x 3/4"

1" x 7/8"

The Standard Die Shoe is more durable and will last longer than the High-production Die Shoe, due to the smaller size of the hole in the base offering more support to the Die Sets (available separately). Standard Die Shoe OR High-production Die Shoe REQUIRED FOR ALL FSS DIE SETS (available separately)! Die Shoes are interchangeable with different FSS Die Sets. Interchangeable FSS Standard Die Shoe Includes: Base with two sizes of pins to maintain correct indexing and assembly and center hole to assist with metal alignment and for removing cut blanks. Aluminum Pusher Plate with two oversized holes Two springs to place between the top and bottom of the Die Sets (Die Sets available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Brand new! Use this tool to make shallow domed forms, such as trinket dishes, box lids, small containers, etc. 2-13/16" diameter. 1/4" thick. Must be used with a large sheet of urethane (available separately). ***Will not fit in the discontinued Potter USA medium press*** Meant to be paired with Pancake Die 1300B. Sample by Lynette Andreasen.

Design: 1-3/16" (30.7mm) Rounded Square Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Design: 1-1/4" diameter (31.75mm) Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Overall size: 2-13/16" x 5/8" Created by Dennis Main on the straight line engraving machine at Potter USA.

Overall size: 3-3/8" x 1". Design size: 2-13/16" x 1/4"

Overall size: 3-3/8" x 1". Design size: 2-13/16" x 1/4"

Two replacement wave springs for FSS dies.

Bag of 10 pieces of urethane for use with impression dies. 95 durometer sheet. Pieces range from approximately 1/2 inch squares. Thickness of each piece is 1/4 inch. Note: These will fray, crack and deform with use, but you will get many uses from them.

This tool steel ring pusher will give you greater detail in your rings when used on impression dies in a hydraulic press. Size: 3" x 1-1/2"

Tool Steel Magnetic Pusher to be used on impression dies in a hydraulic press. 2" diameter. Approx. 3/4" tall, including 1/4" tool steel face. Attaches to upper platen with a magnet.