Overall size: 2" x 6-7/8".

Put a Spring in Your Step with these flowering cowboy boots, just in time for Rodeo season out west! Design: 1-3/16" H each Designed for use in a rolling mill.

11/16" Wide

Overall size: 2" x 6-7/8".

1 1/16" x 3/4" or 27.5mm x 19mm

This die must be used in a hydraulic press. This die measures 1 1/4" x 3/8"

Design: Heart 1-1/4" x 1-3/16" Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

1-1/4" x 3/4"

1" x 7/8"

2 3/8" x 3 7/8"

The Outside Diameter of this Die is 2" Silhouette Die - Medium Circle 7/8". 1 in a series of 6.

The Outside Diameter of this Die is 2" Silhouette Die - Largest Circle 1 1/2 inches.

The Outside Diameter of this Die is 2" Silhouette Die - Small Oval 1 3/16 inch x 9/16 inch

The Outside Diameter of this Die is 2" 1 3/8 inch long x 3/4 inch wide Large Oval

Design: 1" x 1" Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Overall Design Size: approximately 2" x 6-7/8". Each constellation measures about 5/8" at the widest point and would coordinate well with Pancake Die 642A 3/4" Circle. Designed for use in a rolling mill. ***The zodiac names are included on the plate to be a reference point only and not intended to be part of the final design.***

Overall Design Size: approximately 2" x 6-7/8". Designed for use in a rolling mill.

Pancake die: 1/2" wide x 2-1/4" long

Design: 1-1/16" x 5/8" Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Design: 46.6 x 28mm Heart (Same size as PD 701R) Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

This die must be used in a hydraulic press. 3-5/8" x 1-1/16"

Design Size: approximately 2" x 6-7/8". Designed for use in a rolling mill.

Overall size: 2" x 6-7/8".

Pancake Die Small Feather 1 3/4" Long

This die must be used in a hydraulic press. This die measures 1 1/2" x 5/8"

Pancake Die 748 Long Teardrop/Flower Petal2 1/16" x 7/8" Widest Point

This ring is 3" long and 2" at its widest point in the center. This die must be used in a hydraulic press. Customer demo: Piper Lane Davis **FORMERLY R1200**

Ring is 3 inches wide (long) x .25" thick band with oval section is 1" thick.

Pancake Die 710 Large Long Oval 2 1/4" long x 3/4" wide

1/2"x3"

Medium Long Oval Pancake Die 1 1/2" long and 1/2" at widest point and tapers at each end.

This die measures 2 5/8"" wide X 3" tall

Overall Design Size: approximately 2" x 6-7/8". Designed for use in a rolling mill.

Brand new! Use this tool to make shallow domed forms, such as trinket dishes, lockets, small containers, etc. 3" diameter. Coordinated to work with Pancake Die 1538 Sakura Blossom 1/4" thick. Die outer measurements: 4-7/8" x 4-3/4" Must be used with a large sheet of urethane (available separately). ***Will not fit in the discontinued Potter USA medium press***

Brand new! Use this tool to make shallow domed forms, such as trinket dishes, lockets, small containers, etc. 3" wide x 2-5/16"" tall, 1/4" thick. Must be used with a large sheet of urethane (available separately). ***Will not fit in the discontinued Potter USA medium press***

We've brought back this popular design from the November 2017 subscription box, but in a different size! 5/8" x 5/8" (16.5 x 16.5mm)