35.4 x 10mm Customer Demo by Danielle Nicole from Dogwood Designs.

Approx. 16 gauge (due to supply challenges gauges may vary) Design: 1-3/8" x 1-1/16" NOTE: Each stamping is made in-house, one-at-a-time, using vintage tools and processes. The detail in each stamping may vary, and a stamping with less detail is not considered defective.

Design Size: approximately 2" x 6-7/8". Dragonfly measures 1-3/4" x 1". Bee measures 1-3/4" x 1". Butterfly measures 2" x 1". Designed for use in a rolling mill.

Design Size: approximately 2" x 6-7/8". Designed for use in a rolling mill.

This pin comes from the Parisi Tool & Die Co. Design: 5/8" x 7/16"

Design Size: approximately 2" x 6-7/8" Designed for use in a rolling mill.

This floral mandala impression die comes from Villemin in 1900s Paris, France. Design: 27/32" diameter with a 2.5mm setting and multiple 0.5mm settings

This vignette depicts a buck jumping over a countryside fence. From the Rumart collection. Design: 1" x 15/16"

This ornate impression die of scalloped shapes and flowers comes from Villemin in early 1900s Paris, France. Design: 13/16" diameter

Approx. 16 gauge (Due to supply challenges, gauge may vary.) Design: 5/8 x 7/8 NOTE: Each stamping is made in house, one at a time, using vintage tools and processes. The detail in each stamping may vary, and a stamping with less detail is not considered defective.

These tiny critters are ready for you to give them a home! Get five small, round coin shapes featuring a frog, bee/wasp, lizard, dragonfly, and beetle. These are easy to press solid with ~16g sheet. 11mm diameter each. Last photo courtesy of Bottlebee.

Design Dimensions: Left: 3/8" Right: 1/2" x 7/16" from Caaco

Design: Design Size: 2" x 6-3/4"; ~1/8" thick

Approx. 16 gauge (Due to supply challenges, gauge may vary.) Design: 7/8" x 1-1/2" NOTE: Each stamping is made in house, one at a time, using vintage tools and processes. The detail in each stamping may vary, and a stamping with less detail is not considered defective.

Overall Design Size: approximately 2" x 6-7/8". Designed for use in a rolling mill.

Overall size: 2" x 6-7/8".

For use with the Humpback Ring Former Kit to make higher humpback rings. Size: 7/8" T x 2-2/16" L x 1-1/2" W

Overall Design Size: approximately 2" x 7" Designed for use in a rolling mill.

Overall Design Size: approximately 2" x 7" Designed for use in a rolling mill.

This design depicts a decorative quatrefoil design with two links on opposite sides. From Paris, France. Design: 1" x 13/16"

Approx. 16 gauge (due to supply challenges gauges may vary) Design: 1-5/8" diameter NOTE: Each stamping is made in-house, one-at-a-time, using vintage tools and processes. The detail in each stamping may vary, and a stamping with less detail is not considered defective.

This option is for LAYAWAY Payment for the NEW Rincon Press. Manual: $995 Electric: $3,045 This is our newest, most compact, and most economical 20-ton jewelry hydraulic press. This press will work with pancake dies, impression dies, silhouette dies, and even our bracelet-forming frame.

Cat: 39 x 16.5mm. Die: 5-3/4" x 3-1/2"

Use to make humpback rings. Size: 3/4" T x 2-1/4" L x 1" W

Approx. 16 gauge (Due to supply challenges, gauge may vary.) Design: 1-1/4 diameter NOTE: Each stamping is made in house, one at a time, using vintage tools and processes. The detail in each stamping may vary, and a stamping with less detail is not considered defective.

Approx. 16 gauge (Due to supply challenges, gauge may vary.) Design: 3/4" x 1" NOTE: Each stamping is made in house, one at a time, using vintage tools and processes. The detail in each stamping may vary, and a stamping with less detail is not considered defective.

Design: 1-13/16” x 13/16” (45mm x 20mm) Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Design: 1.25” x 0.5” Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

This medallion depicts the sun god Apollo in his chariot, flying across the sky to usher in the morning. The chariot rides upon clouds. Use this design to make pendants, box tops, pins, and more. Design: 1-9/32" diameter

This shot plate includes three patterned designs from Breuning (Pforzheim, Germany) that are usually sold separately. For a limited time, get three dies for the price of one! Left: 9/16" diameter Middle: 3/4" diameter Right: 7/16" diameter

The High-production Die Shoe features a large well in the base to allow for cut blanks to fall out of the bottom of the assembly. NOTE: This High-production Die Shoe base is more delicate than the Standard Die Shoe base and is more prone to damage when over-pressed. Please read ALL instructions before use to learn how to avoid over-pressing. The max gauge for use with the High-production Die Shoe that we recommend is 16 gauge. Opening in base is 1 7/8" x 1 7/8" Standard Die Shoe OR High-production Die Shoe REQUIRED FOR ALL FSS DIE SETS (available separately)! Base is interchangeable with different FSS Die Sets. Interchangeable FSS High-production Die Shoe Includes: Base with two sizes of pins to maintain correct indexing and assembly and large center hole to assist with metal alignment and for collecting and removing cut blanks. Aluminum Pusher Plate with two oversized holes Two springs to place between the top and bottom of the Die Sets (Die Sets available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

This shot plate includes three sought-after designs from Rumart that are usually sold separately. For a limited time, get three dies for the price of one! Sand Dollar: 3/8" diameter Shell: 7/16" x 7/16" Sea Star: 7/16" x 7/16"

Approx. 16 gauge (Due to supply challenges, gauge may vary.) Design: 1-1/8" diameter NOTE: Each stamping is made in house, one at a time, using vintage tools and processes. The detail in each stamping may vary, and a stamping with less detail is not considered defective.

Approx. 16 gauge (Due to supply challenges, gauge may vary.) Design: 1-1/8" x 1-3/4" NOTE: Each stamping is made in house, one at a time, using vintage tools and processes. The detail in each stamping may vary, and a stamping with less detail is not considered defective.

Approx. 16 gauge (Due to supply challenges, gauge may vary.) Design: 1" diameter NOTE: Each stamping is made in house, one at a time, using vintage tools and processes. The detail in each stamping may vary, and a stamping with less detail is not considered defective.

A: 10.3 diameter, 6mm diameter center. B: 11mm diameter, ~3mm diameter center. C: 9.3mm diameter. D: 8.3mm diameter.