Design Size: approximately 2" x 6-7/8" Designed for use in a rolling mill.

Design Size: approximately 1-3/4" x 6-7/8" Designed for use in a rolling mill.

Design Size: approximately 2" x 6-7/8" Designed for use in a rolling mill.

Design Size: approximately 2" x 6-7/8" Designed for use in a rolling mill. Sample earrings by Lynette Andreasen

Design Size: approximately 2" x 6-7/8" Designed for use in a rolling mill.

For use with the Humpback Ring Former Kit to make higher humpback rings. Size: 7/8" T x 2-2/16" L x 1-1/2" W

Brand new! Use this tool to make shallow domed forms, such as trinket dishes, lockets, small containers, etc. 2-13/16" x 1-15/16" 1/4" thick. Must be used with a large sheet of urethane (available separately).

Design: 2-5/8" x 3-1/2" Die itself: 7-1/8" x 5-1/2" Coordinated to work with the Rounded Rectangle Dish Former die DF-014 ***Will not fit in the discontinued Potter USA medium press*** ***Will not fit in Rincon Press

Design Size: approximately 2" x 6-7/8" Designed for use in a rolling mill.

Design Size: approximately 2" x 7" Designed for use in a rolling mill.

Design Size: approximately 2" x 7" Designed for use in a rolling mill.

An assortment of 10 small pieces of aluminum (sizes vary) that can be used to create a force when pressing impression dies. Sizes will vary from 1/2" - 1". Forces work best when the aluminum is pressed hot. ALWAYS CENTER YOUR WORK. Watch the following videos to see Kevin demonstrating how these work: https://www.facebook.com/groups/1253577991351417/?multi_permalinks=7886112968097853&ref=share AND https://www.facebook.com/1640860751/videos/807686980360120/

Design Size: 1-3/8" x 6-5/8" **Please note, the spine design is not straight on the plate, but the plate still functions perfectly fine.** Designed for use in a rolling mill.

Design Size: 2" x 6-3/4" Designed for use in a rolling mill. Sample earrings by Lynette Andreasen

This asymmetrical rectangle features two opposing corners with a curved radius. Perfect for earrings or back plates for contemporary designs. Design: 11/16" x 1" Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

This asymmetrical rectangle features two opposing corners with a curved radius. Perfect for earrings or back plates for contemporary designs. Design: 1" x 1-1/2" Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Design Size: 2" x ~6-11/16" Designed for use in a rolling mill.

Design: 7/8" x 9/16" (22 x 14mm). (Same size/shape as PD1491 that's included in the Riveted Shield Earrings Kit.) Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard or high-production Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Design: 1" x 1/2" Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard or high-production Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Design: 1-1/2" x 3/4" Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard or high-production Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Design Size: 2" x ~6-3/16". Each strip of pattern is approximately 3/8" wide. Sample jewelry made by Jolé Danae Moon. This pattern can be used to make individual jewelry pieces like earrings and cuff links, as well as embellishments for other pieces.

Design Size: 2" x ~6-3/16". Each strip of pattern is approximately 3/8" wide. This pattern plate pairs well with Pancake Die Bracelet B044A 3/8" Thin Bracelet, and Pancake Die Bracelet B044 1/2" Thin Bracelet. .

1-15/16" x 27/32"

The design is 1-7/8" x 2"

This pattern plate was designed to coordinate with some of our bug body impression dies and works well with shotplate die SKU: Bug1 The plate measures approximately 2" x 7", see the photos for measurements of individual wings. Designed for use in a rolling mill.

5-1/2" x 1-1/2" at widest point. Band width 1" tapering to 1-1/2". Die itself 5-13/16" x 7-1/2". Please read note below.

Design: 7/8" diameter Circle Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Design: 3/4" diameter Circle Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Design: 5/8" diameter Circle Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

2" x 6-3/4" Designed for use in a rolling mill.

1-1/32" x 6-1/2" (26.3 x 165mm) Designed for use in a rolling mill.

Design: 15/16" x 5/8" Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Design: 1-7/16" x 1" Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Design: 1-9/16" x 1-1/4" Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Design: 1" flower Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk

Design: 1-1/4" flower Die Set Includes: Die Top, with precision-welded cutter Die Bottom, with precision-registered center hole and metal guide marks on bottom- and right-side edges to assist in lining up metal in the die Urethane: Specific to each die set; not interchangeable with other designs. Color may vary. The components of each Die set are not interchangeable with other die sets, but all can be used with a single, standard Die Shoe. MUST BE USED WITH THE FSS DIE SHOE (available separately) Watch Kevin demonstrate how to use this die: https://youtu.be/7Gl-ShVKtlk